Customer Service & Support: +49 2452 962-450

Business inquiries: +49 2452 962-400

Mon – Fri: 8:00 – 17:00 (CET)

  1. Applications
  2. General dehumidification solutions
  3. Humidity regulation in gas turbine power stations

Humidity regulation in gas turbine power stations

TTR high-performance dehumidifiers increase the profitability

Gas turbine power stations significantly contribute to the coverage of short-term peak loads. A sophisticated humidity regulation helps to prevent the breakdown of individual gas turbines due to corrosion and problems with the electronics. 

Across the globe the climate change, increasingly scarce resources and ever-increasing energy costs call for solutions for a more environmentally friendly and resource-saving power generation. Even though the operating costs of a gas and steam power station are comparatively high due to the low efficiency factor, gas turbine power stations are generally considered a reliable temporary technology for the transition of our energy production to renewable energies. A great deal of the energy input is lost through waste heat and gas turbine cooling.

Therefore it is all the more important to ensure an optimum usage of the energy input and to eliminate potential sources of incidents that could compromise the economical operation or a gas turbine power station or – in the worst case – lead to the failure of individual gas turbines, boilers or pumps. For example due to excessively humid process and regeneration air!

One thing is for sure: Breakdowns will cost you. Gas turbine power stations have to be ready for operation at all times to cover short-term peak loads in the energy supply. If it takes several minutes to start up the turbines, failures and malfunctions can entail tremendous costs!

Securing the operational readiness increases the profitability

A great amount of supply air is required for the smooth operation of gas turbines. Particularly important factors are the air quality and an optimally regulated humidity level. Should the air not be optimally dehumidified, harmful condensate can form inside the plant. Possible consequences are rust, corroded components and failures of the sensitive electronic system.

Trotec's solution: stationary TTR industrial desiccant dehumidifiers

With the stationary desiccant dehumidifiers of the TTR series Trotec offers a highly efficient solution for the individual problems of modern gas and steam power stations in terms of a reliable dehumidification even of large air volumes.

No matter how high the requirements regarding the dehumidification performance of the unit may be: Trotec's product range includes suitable desiccant dehumidifiers for every industrial application scenario.

With a nominal air volume of 750 cubic metres per hour even the smallest industrial desiccant dehumidifier TTR 800 from the comprehensive TTR range provides a sufficient dehumidification performance for the stationary process air dehumidification of individual machines. Ideal conditions for the value retention of the machines and the protection against the harmful condensate formation.

With an immense dehumidification performance of 13,300 cubic metres of dry air per hour the high-performance unit TTR 13500 is positively predestined for a large-scale dehumidification of complete gas turbine power stations – even in cold surroundings of as low as 0 °C and with low dew points.

TTR industrial desiccant dehumidifiers: perfectly geared to your individual needs

All desiccant dehumidifiers of the TTR series can be configured as needed by combining various equipment options. Furthermore, Trotec also offers special models with tailored components as individual solutions.

First-hand expert know-how: contact the Trotec industrial services team

For the planning and implementation of a suitable dehumidification concept you can rely on the expertise the Trotec industrial services team has acquired over many years. Trotec's climate specialists analyse your process workflows and then develop a tailor-made solution based on this requirement situation.

Further solutions

Upon request, we also produce customized desiccant dehumidifiers as special models

Upon request, we will readily produce tailor-made desiccant dehumidifiers as special models “made in Germany” perfectly geared to your needs, e.g.:

  • TTR industrial desiccant dehumidifiers with hygienic design
  • TTR industrial desiccant dehumidifiers for PWIS-free dry air
  • TTR industrial desiccant dehumidifiers with extremely low dew point

Makes use of the possibility of having special models with tailored components for your individual needs planned, designed and manufactured in close consultation with our specialists.
Click here to find out more ...

Further application examples for air dehumidification

  • Environmental simulation climate chamber

    In climatic chambers and wind tunnels three factors need to be simulated at the best possible rate: air temperature, wind strength and humidity. For the latter, the automotive industry needs dehumidifiers, which also perform well at dew points below 0°C, as well as high-performance desiccant dehumidifiers.

    Additional information
  • Dehumidifying & air cleaning for coating

    There are three parameters to be controlled when coating car components: room temperature, humidity and the dust content in the air. In addition to dehumidifiers and heating devices we also provide sustainable air cleaners with special volumetric flow regulation for this production stage in the automotive industry.

    Additional information
  • Dehumidification in tents

    When preparing a tent or another type of temporary accommodation, good room conditions are essential. This applies particularly to makeshift dwellings accommodating large numbers of people. This can be tent cities or container villages for asylum seekers, tent camps for youth groups, tents used as a place to sleep at large events, and also containers serving as a temporary home for seasonal...

    Additional information
  • Drying hygroscopic bulk material

    Varying and too high humidity values can ruin the pourability of powders and granules – and thus entail high consequential costs. In order for hygroscopic bulk material not to go lumpy nor to block hauling paths, the entire air in the chemical and pharmaceutical production must be pre-dried. Using adsorption dryers of the TTR series that's no problem.

    Additional information
  • Drying after silo cleaning

    After the cleaning of storage containers and silos you have to count on them to be fully dried for new bulk material to be protected against moisture from the beginning. And since drying can be effected in a quick and economical manner, we advise decision makers from the chemical and pharmaceutical industry to consider our high-performance dryers of the TTR series.

    Additional information
  • Drying pellets

    Who turns his back on proper air conditioning for production and storage facilities risks serious damage to the product. This is also true for the manufacturing of pellets. The biofuel is particularly susceptible to excessive humidity values. For the untreated raw wood withdraws the humidity from the air and absorbs it. With devastating consequences for both the customer and the manufacturer:...

    Additional information
  • Dehumidification in hotels

    A suitable room climate is a prerequisite for the well-being of hotel guests. If the air in the room is too warm or humid, it appears to be stale and muggy. Often damages appear at the building structure and interior within a short period of time. Wallpaper will be dotted with mould stains, curtains and clothes as well as linen become damp and musty and – if it comes to the worst – mildew runs...

    Additional information
  • Dehumidification in indoor ice-skating rinks

    Due to the difference in temperature between air and the icy surface, condensation inevitably forms in every ice rink – especially when humid air keeps flowing in from outside through the refrigeration system. The solution against dripping water on the ice and against damage to property constitutes a dehumidifier. It prevents condensation in the offing.

    Additional information
  • Drying compressed air

    The most frequent causes for a production stop are too much water vapour in the machines and installations, and corrosion inside the pipelines. Therefore, too humid compressed air should be avoided by all means. An effective option is the use of high-performance dehumidifiers. The answer to the question of how dry the compressed air has to be in order to guarantee optimum production conditions and...

    Additional information
  • Mobile devices for sanitary, heating and ventilation engineers

    Many sanitary, heating and ventilation engineers use the mobile devices from the Trotec Group. Here sanitary, heating and ventilation engineers find everything they regularly need for their daily business to bridge the downtimes of stationary installations – all from a single source: mobile heating devices and central heating units, mobile air handling units or cooling systems right down to...

    Additional information
  • Dehumidification after restoration work

    With an extensive reconstruction flats and houses are being polished up so as to quickly attract potential buyers. Estate agents rely on this service for a better marketability. But home builders also very much appreciate it when their own four walls are in immaculate condition before they move in. The future inhabitants’ thrill of anticipation increases along with the progress in construction...

    Additional information
  • Dehumidification in cinema halls

    A cinema audience essentially wants one thing: to unwind and get away from the daily routine by succumbing to a world of fiction. Loud voices and unwelcome sources of light can be just as annoying as an inappropriately tempered auditorium and a poor air quality. Precisely because it is difficult to properly ventilate cinema facilities, they are usually equipped with powerful air-conditioning...

    Additional information
  • Humidity regulation in gas distribution stations

    The consequences of condensation water and high humidity levels in gas distribution stations are well-known – and expensive: corrosion of pipes, stairways and other metal parts as well as moisture-related failures of the control electronics may entail incalculable costs. If you want to prevent this from the outset, investing in a professional dehumidification system pays off.

    Additional information
  • Offshore: Preventing corrosion

    Corrosion of metal parts in the nacelle of a wind turbine or in the tower itself as well as electrical failure are among the most typical humidity damages in offshore surroundings. They cause substantial additional costs as they increase the expense for maintenance and repair and may lead to operational downtimes. Plus, they reduce the turbine's life. In this case, strategically positioned...

    Additional information
  • Dehumidification in bridges

    Inside bridges, steal beams, electric lines and technical rooms are subject to high humidity. For decades, it has now proven an efficient alternative to high-maintenance anti-rust paint to instead use dehumidifiers to keep bridges dry on the inside. Trotec desiccant dehumidifier of different capacities are used for dehumidification.

    Additional information
  • Humidity regulation in the field of battery production

    Extremely low humidity values, or in other words, an extremely low dew point are indispensable for the production of innovative and environmentally friendly batteries, so as to achieve an optimum product yield and product quality and furthermore ensure a long service life taking all required safety precautions into consideration. Practice-proven dehumidification solutions from Trotec protect...

    Additional information