LD6000 H2 Hydrogen Sensor for trace gas detection
For precise leak detection and tightness tests on sealing sheets, lines and containers
H2 hydrogen sensor - accessory for our LD6000
Using the optionally available hydrogen sensor LD6000 H2, the LD6000 is excellently suited for leak detection with 95/5 forming gas, which is composed of 95% nitrogen and 5% hydrogen.
Owing to its specific structure, hydrogen permeates almost all materials such as soil, concrete or tiles and can then be easily and precisely located on the surface using the hydrogen sensor connected to the LD6000.
The LD6000 indicates the exact concentration of hydrogen. Limit values can be freely adjusted and when exceeded, cause an acoustic and visual signal.
Forming gas of the type 95/5 is neither toxic nor combustible. Therefore, the application for leak detection even in sensitive surrounding areas is generally harmless.
Besides the compact hand sensor, an additional ground sensor with integrated suction pump is available for the detection of even the smallest of trace gas concentrations.
The ground sensor is especially suited for tightness tests or leak detection of green roofs, deep ground wires covered with soil and even asphalt covers etc.
Trace gas hydrogen:
Hydrogen serves as trace gas for leak detection, because it is the lightest of all gases.
Owing to its specific structure, hydrogen very quickly permeates all materials such as soil, concrete, tiles etc.
Upon emerging, the LD6000 H2 sensor registers the hydrogen, which e.g. in the usual 95/5 % forming gas is used as tracer gas for leakages, with a sensitivity level of 1 ppm.
The LD6000 H2 pump kit is as standard already integrated in the hydrogen ground sensor LD6000 H2 (art. no. 3.110.008.020), can however also be ordered individually in order to upgrade older LD6000 H2 ground sensors without integrated pump already in stock.
LD 6000 H2 Hand Sensor
- Response sensitivity: 1 ppm H₂
- Measuring range: Starting at 10 ppm H₂
- Resolution: 1 ppm H₂
- Reaction time: 0.5 s
- Model: Hand sensor with flexible swan-neck (length 50 cm) and approx. 160 cm long connecting lead for LD6000
- Temperature conditions During operation: -10 °C to +60 °C, Storage -20 °C to +60 °C
Pipe location mode
This mode serves to localize pressurized water lines especially those made of plastic, treated with ultrasound by pulse generator LD-PULS.
standard equipment
optionally available
not available
LD6000 H2 Hand Sensor
/en_GB/3110008011/LD-6000-H2-Hand-Sensor-66599-1507646003.jpg)
LD 6000 H2 Hand Sensor
489.95 £ incl. VAT Show net price (VAT not included)
| Technical data | ||
|---|---|---|
| General information | ||
| Article number | 3.110.008.011 | |
| H2gas [ppm] | ||
| Min. measuring range | H2 gas [ppm] | 10 | |
| Max. measuring range | H2 gas [ppm] | 20,000 | |
| Resolution | H2 gas [ppm] | 1 | |
| Response sensitivity | H2 gas [ppm] | 1 | |
| Response time | 0.5 s | |
| Warm-up time | ~ 45 s | |
| Pump kit | ||
| Standard pump capacity [L/min] | ||
| Max. pump capacity (l/min) [l/min] | ||
| Standard pump capacity (mbar) [mbar] | ||
| Max. pump capacity (mbar) [mbar] | ||
| Pump type | ||
| Power supply | ||
| Power input [kW] | ||
| Approx. power input [mA] | ||
| Standard battery capacity ( > 0 °C) [h] | ||
| Battery capacity at maximum pump performance ( > 0°C) [h] | ||
| Material of sensor element | ||
| Other | ||
| Stainless steel | ||
| Aluminium | ||
| Composite | ||
| Polycarbonate | ||
| Material of handle | ||
| Material | Plastics | |
| Plastic/metal | ||
| Metal | ||
| Interfaces / plug design | ||
| Plug design | SDI connector | |
| Special 5-pin plug | ||
| Surrounding conditions (measuring electronics handle) | ||
| Min. operating temperature [°C] | -10 | |
| Max. operating temperature [°C] | 60 | |
| Functions and features | ||
| Robust sinter filter for sensor protection | ||
| Flexible gooseneck | ||
| Integrated connection cable | ||
| Weight | ||
| (packaging excluded) [kg] | 0.5 | |
| Ascertainable measured values and functions | ||
|---|---|---|
| Internal sensors | ||
| H2 hydrogen gas [digits] | ||
| Functions and features | ||
| Robust sinter filter for sensor protection | ||
| Flexible gooseneck | ||
| Integrated connection cable | ||
| Functional knob with connected active suction pump | ||
| Shielded sensor tip for penetration of soft ground | ||
| Rubber sleeve for better sealing | ||
| Sinter protection cap | ||
| Screw-on hollow extension rods | ||
standard equipment
optionally available
not available
LD6000 H2-Ground Sensor
/en_GB/3110008020/LD6000-H2-Ground-Sensor-incl.-Pump-kit-66595-1507646004.jpg)
LD6000 H2-Ground Sensor incl. Pump kit
849.95 £ incl. VAT Show net price (VAT not included)
| Technical data | ||
|---|---|---|
| General information | ||
| Article number | 3.110.008.020 | |
| H2gas [ppm] | ||
| Min. measuring range | H2 gas [ppm] | 10 | |
| Max. measuring range | H2 gas [ppm] | 20,000 | |
| Resolution | H2 gas [ppm] | 1 | |
| Response sensitivity | H2 gas [ppm] | 1 | |
| Response time | 0.5 s | |
| Warm-up time | ~ 45 s | |
| Pump kit | ||
| Standard pump capacity [L/min] | 1.5 | |
| Max. pump capacity (l/min) [l/min] | ||
| Standard pump capacity (mbar) [mbar] | ||
| Max. pump capacity (mbar) [mbar] | ||
| Pump type | ||
| Power supply | 9 V | |
| Power input - addition | With unrestricted flow | |
| Approx. power input [mA] | 45 | |
| Standard battery capacity ( > 0 °C) [h] | ||
| Battery capacity at maximum pump performance ( > 0°C) [h] | ||
| Material of sensor element | ||
| Other | ||
| Stainless steel | ||
| Aluminium | ||
| Composite | ||
| Polycarbonate | ||
| Material of handle | ||
| Material | Plastics | |
| Plastic/metal | ||
| Metal | ||
| Interfaces / plug design | ||
| Plug design | Special 5-pin plug | |
| SDI connector | ||
| Surrounding conditions (measuring electronics handle) | ||
| Min. operating temperature [°C] | -10 | |
| Max. operating temperature [°C] | 60 | |
| Min. storage temperature [°C] | ||
| Max. storage temperature [°C] | ||
| Functions and features | ||
| Screw-on hollow extension rods | ||
| Functional knob with connected active suction pump | ||
| Rubber sleeve for better sealing | ||
| Integrated connection cable | ||
| Dimensions | ||
| Length (packaging excluded) [mm] | 960 | |
| Width (packaging excluded) [mm] | 95 | |
| Height (packaging excluded) [mm] | 95 | |
| Diameter (packaging excluded) [mm] | 95 | |
| Weight | ||
| (packaging excluded) [kg] | 1.1 | |
| Ascertainable measured values and functions | ||
|---|---|---|
| Internal sensors | ||
| H2 hydrogen gas [digits] | ||
| Functions and features | ||
| Screw-on hollow extension rods | ||
| Functional knob with connected active suction pump | ||
| Rubber sleeve for better sealing | ||
| Integrated connection cable | ||
| Flexible gooseneck | ||
| Shielded sensor tip for penetration of soft ground | ||
| Robust sinter filter for sensor protection | ||
| Sinter protection cap | ||
standard equipment
optionally available
not available